hbd dc-dc series data sheet 30 to 60-watt, dual output rev. jan 26, 2005 page 1 of 3 www.power-one.com hbd060yge-a 60 65 70 75 80 85 10 20 30 40 50 60 70 80 90 100 load % eff. (18v) eff. (24v) eff. (36v) 50 55 60 65 70 75 80 85 10 20 30 40 50 60 70 80 90 100 load % efficiency % hbd060zge-a hbd040zge-a hbd0x0zed-a technical specifications voltage range 24 vdc nominal 18.00 - 36.00 vdc 48 vdc nominal 34.00 - 75.00 vdc reflected ripple 80 ma input reverse voltage protection shunt diode hbd dual output, dc-dc converters feature high efficiency, 1500 vdc isolation, and open-frame packaging. the hbd family allows board designers to deliver any combination of power from either output, up to each model?s maximum rating. the hbd is available in 5v/3.3v or 3.3v/2.5v combinations in either a 24v or 48v input version. the hbd uses planar magnetics and has an mtbf of over a million hours. ? independent dual outputs ? flexible load sharing ? high efficiency topology ? open-frame design ? planar magnetics ? independent trim for each output ? 1500v isolation ? 100c baseplate operation description features input efficiency vs. load (24v input) efficiency vs. load (48v input) notes 1 for negative logic, add suffix ?n? to model number. ? mtbf predictions may vary slightly from model to model. specifications typically at 25c, normal line, and full load, unless otherwise stated. soldering conditions: i/o pins, 260c, ten seconds; fully compatible with commercial wave-soldering equipment. safety: agency approvals may vary from model to model. please consult factory for specific model information. units are water-washable and fully compatible with commercial spray or immersion post wave-solder washing equipment. turn-on time 10 ms remote shutdown positive logic switching frequency 500 khz isolation input - output 1500 vdc input - case 1050 vdc output - case 500 vdc temperature coefficient 0.03%/c case temperature operating range -40 to +100c storage range -40 to +125c thermal shutdown range 105 to 115c humidity max., non-condensing 95% vibration, 3 axes, 5 min each 5 g mtbf ? (bellcore tr-nwt-000332) 1.3 x 10 6 hrs safety ul, cul, vde weight (approx.) 2.4 oz general setpoint accuracy 1% line regulation v in min. - v in max., i out rated, output 1 0.2% v out line regulation v in min. - v in max., i out rated, output 2 1.0% v out load regulation i out min. - i out max., v in nom., output 1 0.5% v out load regulation i out min. - i out max., v in nom., output2 1.0% v out minimum output current 10% i out rated dynamic regulation, loadstep 25% i out pk deviation 4% v out settling time 500 s voltage trim range (5v/3.3v units) 10% power limit threshold range, % of i out rated 110 - 140% ovp trip range (main ouput) 115 - 140% v out nom. output
hbd dc-dc series data sheet 30 to 60-watt, dual output rev. jan 26, 2005 page 2 of 3 www.power-one.com model input voltage input voltage maximum input output rated output ripple & noise typical (volts) range (volts) current (amps)* voltage (volts) current (amps)&& pk-pk (mv) efficiency** hbd040yed-a 24 18-36 2.89 3.3/2.5 12/15 75/75 75% hbd060yge-a 24 18-36 4.54 5.0/3.3 12/15 100/75 78% hbd040yge-a 24 18-36 3.02 5.0/3.3 8/12 100/75 80% hbd030zed-a 48 34-75 1.50 3.3/2.5 9/12*** 75/75 75% hbd040zge-a 48 34-75 1.51 5.0/3.3 8/12 100/75 80% hbd040zed-a 48 34-75 1.62 3.3/2.5 12/15 75/75 75% hbd060zge-a 48 34-75 2.27 5.0/3.3 12/15 75/75 75% notes: * maximum input current at minimum input voltage, maximum rated output power. ** at nominal v in , rated output. *** total output power to be restricted to 30 watts. && current can be drawn from either output to its maximum value, or from both outputs to a combined total of 15a. thermal impedance natural convection 6.6 c/w 100 lfm 5.7 c/w 200 lfm 4.2 c/w 300 lfm 3.1 c/w 400 lfm 2.6 c/w tolerances note: thermal impedance data is dependent on many environmental factors. the exact thermal performance should be validated for specific application. mechanical drawing 1-v in 2 case 3 on/off 4+v in 5+v out 2 6- v out 2 7 trim 2 8+v out 1 9-v out 1 10 trim 1 inches: (millimeters) .xx 0.020 .x 0.5 .xxx 0.010 .xx 0.25 pin: 0.002 0.05 (dimensions as listed unless otherwise specified.) pin function 10 9 8 7 6 5 4 3 2 1 bottom view side view (pin side) 1.500"(38.1mm) 1.200"(30.5mm) 0.900"(22.9mm) 0.500"(12.7mm) 0.200"(5.1mm) -0.100"(-2.5mm) 1.700"(43.2mm) -0.50"(-12.7mm) -0.300"(-7.6mm) 1.400"(35.6mm) 1.000"(25.4mm) 0.400"(10.2mm) 0 (12.7mm) 0.50" (0.6mm) .025" ref. (1.0mm) dia 0.040" (4.6mm) 0.18" (61.0mm) 2.40 " (57.9mm) 2.28 " m3x.5 through 4pl mounting inserts 0 (-4.8mm) -0.19" (48.3mm) 1.900" model selection
rev. jan 26, 2005 page 3 of 3 www.power-one.com series applicability: has, hbd, hbs, hes, qbs, qes, tes, tqd features & options descriptions suffix code remote on/off positive logic none negative logic n trim standard power-one (negative) none industry-standard (positive) t pin length 0.18? (4.6mm), standard model length none 0.145? (3.68mm) 7 0.110? (2.8mm) 8 special options customer-specific models s# note: contact factory for availability of specific options. nuclear and medical applications - power-one products are not designed, intended for use in, or authorized for use as critical c ompo- nents in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of power-one, inc. technical revisions - the appearance of products, including safety agency certifications pictured on labels, may change dependin g on the date manufactured. specifications are subject to change without notice. ordering information suffix code identification: options
|
